Tool holder for angle and stop angle

The universal tool holder can hold the following tools: Screwdriver Open-end spanner, open-end box wrench pliers, scissors etc. all bar-like tools with round or polygonal cross-sections Measuring equipment and other tools. With a magnetic holding force of two times 20 N per holder it is the universal talent among tool holders.  The variable concept of the universal tool holder makes unused special holders from set offers a thing of the past: The tool holder adapts to the requirements of the workplace. If required, it can be clipped onto the universal clamping rail with a single movement! Completely without tools and without further securing! It can be removed just as quickly. Horizontally, the holder can be moved continuously on the clamping rail. The lateral stop bar ensures vertical alignment of the tool. The stop is set to the right, left, double-sided or passive by simply changing the position.The tool is located 30 mm away from the rear edge of the holding rail. This allows quick and easy access to the tool and its return. Minimum purchase: 25 pieces

Screwdrivers and similar tools with a diameter of less than 13 mm are quickly and ergonomically accessible via the quiver holder.The holder is an alternative for tools without iron components, which do not stick to the magnetic universal tool holder.The quiver holder is fixed with a sliding nut and a knurled screw (included in the scope of delivery) is attached to the lower link of the universal clamping rail.

Stable tool holder for 1,000 g hammer or mitten. Safely encloses the tool to prevent it from falling out.  The tool is approx. 30 mm away from the wall and can therefore be positioned easily and precisely. Prepared for mounting on the K.Lean universal clamping rail. Can also be mounted directly on a wall. Manufactured from indestructible stainless steel sheets. Dimensions: 174 x 90 x 30 mm

Phillips screw for fastening the universal terminal strip at the front. Sold in packs of 100.

Professional holder, developed for variable tool use, fast and safe handling: Simply hook it in and touch the magnetic holder. Manufactured from stainless steel sheet. Dimensions HxDxW 65 x 60 x30 mm

A tool holder whose clamping force can be perfectly adjusted was the wish of our customers. We have fulfilled this request and developed this intelligent tool holder. By means of the adjusting screws you can ideally adjust the width and pretension of the tool clamping range. This guarantees maximum efficiency and ergonomics. Available sizes (adjustment ranges): 0-10 mm 11-30 mm Currently only available on request.

The tool is approx. 30 mm away from the wall and can therefore be positioned easily and precisely. Prepared for mounting on the K.Lean universal clamping rail. Manufactured from indestructible stainless steel sheets. Dimensions: 174 x 90 x 30 mm

Manufactured as angle bracket for universal mounting on the tool trolley. The angle grinder is hooked into the shaped pocket. Optionally you can get a screw-on cable hook to clean up cable-operated angle grinders. Dimensions: 162 x 140 x 60 mm

Locating bolt for sockets 1⁄4" for slide nut M4 Dimensions: 6.3 - M4 mm Minimum purchase: 25 pieces

With this quiver you create a storage possibility for your screwdrivers directly at the place of use. This way you have integrated the most important tools directly into your work process. In addition, the workplace is free and tidy while you do not need the tools. You can place the screwdriver quiver directly in position to ensure quick and ergonomic access. This tool holder is especially designed for assembly lines, production lines, cycle workstations and 5S workbenches. For screwdrivers, cordless screwdrivers, electric screwdrivers, torque screwdrivers, pistol screwdrivers, impulse screwdrivers, compressed air screwdrivers, electric rod screwdrivers or any other tool. Made of solid sheet steel and plastic  Protects the tool from damage Ensures free and tidy work area Large O-ring, as anti-slip protection for cordless screwdrivers with tools. Stable, suitable for workshops D = 54 - 52 mm Adjustable in three dimensions height: 30mm

The K.Lean tool holders are variably attached to the patented universal clamping rail. The clamping rail is extruded from aluminium profiles and anodised. Together with the separately available tool holders, it offers a unique, linear and flexible organization system. In free-floating use, the clamping rail unfolds its full potential: The system offers access to the tools, transparent workstations and additional depth (which benefits the offset mounting of tool shadows or special holders). The rail's closed top profile prevents coarse soiling. Sliding nut slides are located at the back and at the bottom, which can be used toattach various accessories(special holders, tool shadows). The universal clamping rail is part of the workbench attachments and the mounting trolley. It is available individually and by the metre for individual designs and applications. The clamping rail can be easily attached to walls and other flat surfaces in addition to the floating installation.

The distance angle bracket allows the universal clamping rail to be fixed to the wall for an even greater distance between the tool and the wall and allows the rail to be positioned at the desired angle for ergonomic tool handling. The angle can be adjusted as required. 2 pcs. distance angle bracket (003.4.552) 2 pcs. thread furrow- de screw M 6 x 16 (003.4.665) 4 oval head screw M 6 x 12 (003.4.515) 4 pcs. locking tooth nut M 6 (003.4.525) Dimensions: 95 x 70 x 25 x 2 mm Material: stainless steel Distance from the middle of the rail to the wall: 60 / 70 / 80 mm Attention: The universal clamping rail is not included in this set! You can buy it in your desired length.

Stable tool holder for 1,000 g hammer or mitten. Safely encloses the tool to prevent it from falling out.  The tool is approx. 30 mm away from the wall and can therefore be positioned easily and precisely. Prepared for mounting on the K.Lean universal clamping rail. Can also be mounted directly on a wall. Manufactured from indestructible stainless steel sheets. Dimensions: 174 x 90 x 30 mm

Avec la station de charge de batterie K.Lean, vous disposez d'un outil pour mettre en œuvre les 5S et la gestion Lean dans votre entreprise de manière simple et efficace. Chaque chargeur de batterie pour un chariot élévateur à fourche est muni de l'étiquette de sécurité appropriée. Cela inclut en fait les équipements de sécurité au travail tels que les douches oculaires et les gants antiacides. En outre, chaque chargeur de batterie occupe une connexion électrique. Connaissez-vous la situation où un employé veut charger le chariot élévateur pendant la nuit, mais qu'il n'a pas vu que son collègue avait débranché le câble du chargeur pour brancher un autre appareil ? Les coûts que vous encourez parce que vos employés ne peuvent pas travailler parce que le chariot élévateur est vide sont immenses.  Évitez cela avec le chargeur de batterie K.Lean. Le câble principal reste toujours branché et, grâce au distributeur d'alimentation attaché avec le RCCB, vos employés peuvent toujours connecter rapidement un appareil. Le support joint comprenant une douche oculaire au cas où un employé se blesse. Vous pouvez également placer des gants et des lunettes de sécurité sur la planche de stockage, qui sont nécessaires pour la charge lors de la manipulation de l'acide des batteries. Comme le chariot est sur roues, vous pouvez le déplacer à tout moment pour nettoyer en dessous ou derrière lui. Grâce à l'étiquetage de la station de recharge de batteries, chaque employé sait immédiatement de quoi il s'agit. La visualisation selon 5S est ainsi parfaitement mise en œuvre et la vie de vos employés est facilitée. Variantes possibles de distribution d'électricité : Variante 1 : Sans distributeur d'électricité Variante 2 : Dans cette version, vous recevrez un distributeur d'électricité avec un câble d'alimentation de 2 m de long avec une prise de 16 A. Les prises de courant sont 2x 16A et 2x 220V. Disjoncteur FI et disjoncteur automatique inclus. Variante 3 : Dans cette version, vous recevrez un distributeur de courant avec une ligne d'alimentation de 2 m de long et une prise de 32 A. Les prises de courant sont 1x 32A, 1x 16A et 2x 220V. Disjoncteur FI et disjoncteur automatique inclus. Autres notes sur la station de recharge des batteries : La livraison a lieu sans Chargeur de chariot élévateur ! Vous pouvez trouver un exemple de mode d'emploi dans l'onglet PDF ici dans l'article ou  . Vous devez les adapter à votre entreprise. Veuillez nous contacter pour recevoir un modèle Word modifiable. Dimensions du chargeur Les dimensions maximales de l'espace pour le chargeur de batterie de votre camion sont (largeur x hauteur x profondeur) : 620 x 795 x 400 mm.  Nous recommandons que le chargeur soit légèrement plus petit, car vous devrez le placer dans cette pièce.

A tool holder whose clamping force can be perfectly adjusted was the wish of our customers. We have fulfilled this request and developed this intelligent tool holder. By means of the adjusting screws you can ideally adjust the width and pretension of the tool clamping range. This guarantees maximum efficiency and ergonomics. Available sizes (adjustment ranges): 0-10 mm 11-30 mm Currently only available on request.